|
|
| 产品展示 |
|
RENOLIN CKC 100详细说明 （浏览1921次）
RENOLIN CKC
High Performance CKC Gear Oils High Performance CKC Gear Oils
Gearboxes designed for the transfer of power or torque can only perform effectively when excessive wear which can occur at high or fluctuating loads, particularly around the reference circle, is avoided. The life of a gearbox depends on the correct selection of the most suitable lubricating oil. The principal function of a gear oil is not just to lubricate bearings and the gears themselves, i.e. to reduce friction and avoid wear but also to provide protection against corrosion, to cool and to seal. The RENOLIN CKC gear oils contain carefully selected base oils and matched additives to protect machinery from undue wear in especially critical boundary friction conditions. RENOLIN CKC products can be classified as CKC lubricating oils according to ISO 6743-6.
The special characteristics of RENOLIN CKC series lubricants are:
- High pressure absorption and excellent wear protection
- Good viscosity-temperature behaviour and excellent low-temperature characteristics
- Good corrosion protection for steel and nonferrous metals
- Good resistance to ageing
- Good compatibility with sealing materials
- Low foaming
- Avoidance of frictional vibration by the use of surface-active additives
- Good demulsification characteristics
- Multipurpose applications
Application:
RENOLIN CKC series oils are recommended for all industrial applications where the machinery manufacturer recommends the use of a CKC type oil. Highly-stressed bearings, joints, pressure spindles, spur and worm drive gears are reliably, effectively and economically lubricated at temperatures of up to 120°C. The use of these oils guarantees the quiet and smooth running of machinery along with optimum operational reliability. The use of these oils also allows drain intervals to be extended. Please consult our Application Engineers for suggestions on how this series of oils can be used to rationalize oil stocks.
| RENOLIN CKC |
|
100 |
150 |
220 |
320 |
460 |
680 |
|
| Lubricating oil type |
|
|
|
|
|
|
|
|
| acc. to ISO 6743-6 |
|
CKC 100 |
CKC 150 |
CKC 220 |
CKC 320 |
CKC 460 |
CKC 680 |
|
| acc. to DIN 51 502 |
|
CLP 100 |
CLP 150 |
CLP 220 |
CLP 320 |
CLP 460 |
CLP 680 |
|
| Characteristics |
Unit |
|
|
|
|
|
|
Test method |
| Colour |
|
2 |
3 |
4 |
4.5 |
5 |
5 |
ASTM D 1500 |
| Kinematic viscosity |
|
|
|
|
|
|
|
|
| at 40 °C |
mm²/s |
94.4 |
145.6 |
214 |
331 |
468 |
690 |
ASTM D 445 |
| at 100 °C |
mm²/s |
11.1 |
14.5 |
18.5 |
24.6 |
30.8 |
36.8 |
ASTM D 445 |
| Viscosity index |
|
102 |
98 |
96 |
96 |
95 |
87 |
ASTM D 2270 |
| Density at 15 °C |
kg/l |
0.884 |
0.89 |
0.895 |
0.9 |
0.903 |
0.922 |
ASTM D 1298 |
| Flash point, Cleveland open cup |
°C |
220 |
225 |
230 |
230 |
240 |
245 |
ASTM D 92 |
| Pour point |
°C |
– 27 |
- 24 |
- 21 |
- 15 |
– 12 |
– 12 |
ASTM D 97 |
| Neutralization number |
mg KOH/g |
0.33 |
0.33 |
0.33 |
0.33 |
0.33 |
0.33 |
ASTM D 974 |
| Saponification number |
mg KOH/g |
1.3 |
0.84 |
0.84 |
0.84 |
0.84 |
0.84 |
ASTM D 94 |
| Sulphate ash |
% mass |
0.1 |
0.1 |
0.1 |
0.1 |
0.1 |
0.1 |
ASTM D 874 |
| Water content |
% mass |
not traceable |
not traceable |
not traceable |
not traceable |
not traceable |
not traceable |
ASTM D 95 |
| Insolubles |
% mass |
not traceable |
not traceable |
not traceable |
not traceable |
not traceable |
not traceable |
DIN 51 592 |
| Demulsification |
min |
< 20 |
< 20 |
< 20 |
< 20 |
< 20 |
< 20 |
DIN 51 599 |
| Foaming, |
|
|
|
|
|
|
|
|
| seq. I |
ml |
< 10/0 |
< 10/0 |
< 10/0 |
< 10/0 |
< 10/0 |
< 10/0 |
ASTM D 892 seq. I-III |
| seq. II |
ml |
< 10/0 |
< 10/0 |
< 10/0 |
< 10/0 |
< 10/0 |
< 10/0 |
ASTM D 892 seq. I-III |
| seq. III |
ml |
< 10/0 |
< 10/0 |
< 10/0 |
< 10/0 |
< 10/0 |
< 10/0 |
ASTM D 892 seq. I-III |
| Copper corrosion |
degree of corr. |
1a-100A3 |
1a-100A3 |
1a-100A3 |
1a-100A3 |
1a-100A3 |
1a-100A3 |
ASTM D 130 |
| Rust prevention |
|
pass B |
pass B |
pass B |
pass B |
pass B |
pass B |
ASTM D 665 |
| Ageing behavior, |
|
|
|
|
|
|
|
|
| viscosity increase |
% |
1 |
1 |
1 |
1 |
1 |
1 |
ASTM D 2893 |
| precipitation number increase |
ml |
< 0.05 |
< 0.05 |
< 0.05 |
< 0.05 |
< 0.05 |
< 0.05 |
ASTM D 2893 |
| FZG mechanical gear rig test |
load stage |
12 |
12 |
12 |
12 |
12 |
12 |
DIN 51 354-2 |
| Effect on SRE-NBR 1 seal material acc to DIN 53 538-1 at 100 °C +/– 1 °C after 7 days +/– 2 hours, |
|
|
|
|
|
|
|
|
| relative volume change |
% |
7 |
7 |
7 |
7 |
7 |
7 |
DIN 53 521 together with DIN 53 505 |
| change in Shore A hardness |
Shore |
- 3 |
- 3 |
- 3 |
- 3 |
- 3 |
- 3 |
DIN 53 521 together with DIN 53 505 | |
|
|
